不锈钢控制柜是一种主要用于安装电气设备的机柜，一般用于供电系统，包括高低压配电柜等。使用时，内部电气设备应按照一定的标准进行安装。那么如何布置不锈钢控制柜。我们来看看下面的介绍。

Stainless steel control cabinet is a type of cabinet mainly used for installing electrical equipment, generally used in power supply systems, including high and low voltage distribution cabinets. When in use, internal electrical equipment should be installed according to certain standards. So how to arrange the stainless steel control cabinet. Let's take a look at the introduction below.

（一）需要注意的事项是重型建筑物的电气控制元件安装在集热板的下方，而加热反应元件应安装在不锈钢控制柜的上部或后部，但应放置在下部热继电器内。由于热继电器的出口端通过电动机直接连续地连接方便企业的出口，线路的入口端直接连续地连接交流接触器，因此系统接线短方便，适用于不同的冷却方式。

（1） It should be noted that the electrical control components of heavy-duty buildings are installed below the collector plate, while the heating reaction elements should be installed above or behind the stainless steel control cabinet, but should be placed inside the lower thermal relay. Due to the fact that the outlet end of the thermal relay is directly and continuously connected to the enterprise's outlet through an electric motor, and the inlet end of the circuit is directly and continuously connected to the AC contactor, the system wiring is short and convenient, suitable for different cooling methods.

（2）强隔音隔音对外界环境的屏蔽作用较弱。

(2) Strong sound insulation has a weaker shielding effect on the external environment.

(3) 电气元件的频繁维护和安装的必要性不应过高或过低。手动开关的设备方位和仪器的连续监测应符合人机工程学的原则。不锈钢控制柜系统应进行管理和清洁。清洗前，在电子元器件上盖上散热孔，防止灰尘进入，影响元器件的工作。对于清洁，我们可以使用真空吸尘器，这不符合吹与数据质量的压缩空气的要求。因为我们的压缩空气会将水蒸气和灰尘吹进元件中，这种比较简单而且容易形成短路，这样会影响不锈钢控制柜的正常运行和应用。

(3) The necessity of frequent maintenance and installation of electrical components should not be too high or too low. The equipment orientation of manual switches and the continuous monitoring of instruments should comply with the principles of ergonomics. The stainless steel control cabinet system should be managed and cleaned. Before cleaning, cover the electronic components with heat dissipation holes to prevent dust from entering and affecting their operation. For cleaning, we can use a vacuum cleaner, which does not meet the requirements for blowing compressed air with data quality. Because our compressed air will blow water vapor and dust into the components, which is relatively simple and prone to short circuits, it will affect the normal operation and application of the stainless steel control cabinet.

(4) 电气系统元件的配备考虑了工作距离，学生可以将结构规模相近整洁美观对称的电器组合在一起，便于数据处理安装和接线。选择不同的接线继电器控制方式时，应适当加大旅游线路的电气调整，并保持线路的布局。

(4) The configuration of electrical system components takes into account working distance, and students can combine electrical appliances with similar, clean, aesthetically pleasing, and symmetrical structures for easy data processing, installation, and wiring. When selecting different wiring relay control methods, it is necessary to appropriately increase the electrical adjustment of tourist routes and maintain the layout of the routes.

（5）确定各电气控制元件的方向后，可根据电气图进行布置。根据图的轮廓。工程设备绘制成电气元件，即在不违反其轴线的情况下，象征性地分析每个电子元件之间的距离。各企业的电气元件的规模和服务应按本规范的标准执行，以保证建筑安装板顺利通过安装和各种电气加工产品的质量。电气柜内有大型电器元件，要安装在两个安装梁之间，这样外壳是否能有效减轻自身重量，节省教材，方便我们安装。此外，在规划中还应考虑竖向结构尺度。

(5) After determining the direction of each electrical control component, it can be arranged according to the electrical diagram. According to the outline of the diagram. Engineering equipment is depicted as electrical components, symbolically analyzing the distance between each electronic component without violating its axis. The scale and service of electrical components in each enterprise should be carried out in accordance with the standards of this specification to ensure the smooth installation of building installation boards and the quality of various electrical processing products. There are large electrical components inside the electrical cabinet that need to be installed between two installation beams. Can the shell effectively reduce its own weight, save textbooks, and facilitate our installation. In addition, the vertical structural scale should also be considered in the planning.

(6) 在不锈钢控制柜的布局设计中，还提倡输入插座元件的数量插座引线的尺寸和方向，以及根据相关时序电路选用进口端子和连接器。

(6) In the layout design of stainless steel control cabinets, the number of input socket components, the size and direction of socket leads, and the selection of imported terminals and connectors based on relevant timing circuits are also advocated.